FIME Extractor Baxi Roca Laura Plus 28/28 F - Ref. 122220500 (GR03030)
FIME extractor for Baxi Roca Laura Plus 28/28 F. It is the turbine that expels the combustion gases. The manufacturer FIME and the factory model GR03030 are cast into the housing; the sales reference is 122220500. Replacement requires first confirming the fault of the part through technical diagnosis, even when the extractor fails or does not rotate normally.
- Type of part
- Extractor fans
- Status
- Refurbished
- internal SKU
- ECRLP2828F
- Warranty
- 1 year
Compatible Baxi Roca boilers
Extractor. A proven compatibility: PLUS 28/28 F.
Proven compatibility
| Boiler model | Family | Verification |
|---|---|---|
| Baxi Roca PLUS 28/28 F | LAURA | Contrasted |
Can't see your model or have questions? The printed reference takes precedence. How to check it · Send us a photo via WhatsApp.
How to check if it is the part for your boiler
The part reference, model, and equipment revision must be verified against the manufacturer's documentation.
- Find the reference printed on the installed part and check whether it matches the catalogue reference —. If it is not visible, do not identify the part by its shape alone.
- Check the full boiler model on its data plate and look for it in the model associations on this page.
- Compare the connections and physical body with the original part before installation.
- If anything is unclear, send us a photo of the marking via WhatsApp before placing your order.
Symptoms that require diagnosis in the extractor
The extractor evacuates the combustion gases with forced draft. These are the typical symptoms and what to do:
Common symptoms and faults
- 01
The extractor makes noise or vibrates when it rotates.
Cause: The impeller may be unbalanced or the bearing worn out due to use.
Turn the impeller by hand with the boiler unplugged; if you feel rubbing or vibration, the wear is confirmed.
- 02
The boiler does not ignite or gets locked when trying to start.
Cause: If there is not enough airflow, the pressure switch does not close and the control board does not allow ignition.
Check that the flue pipe is not blocked from the outside before considering the extractor as faulty.
- 03
The impeller is stuck and does not rotate, or it is very difficult to move.
Cause: Dirt or accumulated rust can block the shaft, especially after a prolonged stop.
With the boiler turned off, try to turn the impeller by hand; if it is completely blocked, confirm the fault before purchasing the part.
- 04
The boiler starts the fan but locks out after a few seconds.
Cause: If the extractor does not reach the necessary revolutions, the flow is insufficient and the safety lock is activated.
Check if the extractor receives stable power during the ignition attempt before replacing it.
These symptoms can have more than one cause. If your boiler displays a fault code, send it to us via WhatsApp along with a photo of the labeling, and we'll tell you if this is the part.
Data sheet for the Baxi Roca extractor.
- Uniclima internal SKU
- ECRLP2828F
- Brand
- Baxi Roca
- Type of part
- Extractor fans
- Units in stock
- 2 units
- Status
- Refurbished
- Warranty
- 1 year
- Shipping
- Delivery time shown at checkout
- Return
- 14 days
Part data and available documentation
Contrast the label codes, PCB, and revision with the installed part; they are not necessarily equivalent references.
- Manufacturer of the part
- FIME
- Factory model
- GR03030 (reading of)
- Reference code (adhesive label)
- 122220500
Manuals and technical documentation
Official documentation of the boiler, useful for locating the part and cross-referencing the fault codes.
- Baxi Roca PLUS 28/28 F Manual (PDF) Document © Baxi Roca, provided as a technical reference.
Frequently asked questions about the extractor
Which manufacturer is this extractor from the Baxi Roca Laura Plus 28/28 F?
What is the sales reference for this extractor?
When should this extractor of the Laura Plus 28/28 F be replaced?
