Airsol HKB 224 PCB Ref. 3001060232
The Airsol HKB 224 PCB Ref. 3001060232 is used in boilers from the Heatline Compact range, such as the S24 and S30 models, among others. This board is the component that controls the ignition, burner modulation, pump, and safety functions of the boiler. If it has faults, you will notice that the boiler does not start, locks out, or behaves erratically. It is advisable to replace it when errors such as F63, F64, F65, F67, or F70 appear, as they indicate problems with the memory or the signal of the board.
VAT included
Consult via WhatsAppAirsol boilers compatible with reference 3001060232
PCB with reference 3001060232. Four confirmed compatibilities: S24 and S24S.
Proven compatibility
| Boiler model | Family | Verification |
|---|---|---|
| Airsol S24 | Heatline Compact (non-condensing / Airsol HK B124) | Contrasted |
| Airsol S24S | Heatline Compact (non-condensing / Airsol HK B124) | Contrasted |
| Airsol S30 | Heatline Compact (non-condensing / Airsol HK B124) | Contrasted |
| Airsol S30S | Heatline Compact (non-condensing / Airsol HK B124) | Contrasted |
Can't see your model or have questions? The printed reference takes precedence. How to check it · Send us a photo via WhatsApp.
How to check if ref. 3001060232 is the part for your boiler
What determines it is not the boiler model, but the reference printed on the part you already have installed.
- Find the reference printed on the installed part and check whether it matches the catalogue reference 3001060232. If it is not visible, do not identify the part from its shape alone.
- Check the full boiler model on its data plate and look for it in the model associations on this page.
- Compare the connections and physical body with the original part before installation.
- If anything is unclear, send us a photo of the marking via WhatsApp before placing your order.
Symptoms and faults that the PCB 3001060232 resolves.
The PCB controls the ignition, modulation, and safety features of the boiler. These are the typical symptoms and what to do:
Common symptoms and faults
- 01
The control panel with the screen goes dark, but when touching the boiler's panel, it is noticeable that it still has power.
Cause: The display is a separate module that receives data from the PCB via a flat cable; if that connection fails, the screen turns off even though the board continues to operate.
Disconnect and reconnect the flat cable properly at both ends and check that there are no bent pins.
- 02
No button on the remote does anything, neither power on nor temperature adjustment.
Cause: If the main PCB does not process the commands, the display module may remain lit but unresponsive.
Measure with a multimeter that the PCB is receiving the 230V input and that the fuse is not blown before replacing it.
- 03
The boiler ignites, runs for a while, and then stops on its own without any fault code being triggered.
Cause: An internal fault in the PCB can lose the flame maintenance signal without generating a recognizable fault code.
Cut the power for a couple of minutes and restart to rule out a temporary blockage before declaring the PCB faulty.
- 04
The display flickers or shows random characters that do not form any stable code.
Cause: It is usually a false contact between the PCB and the display module due to the flat cable connector, not a fault of the display itself.
Carefully move the flat cable while the boiler is on and observe if the blinking changes; if so, the problem is in the connection, not in the PCB.
Fault codes for Airsol that this part resolves.
| Code | Fault | Diagnosis and solution |
|---|---|---|
| F63 | Fault in the main PCB memory | The EEPROM/circuitry of the PCB is corrupted or out of tolerance; if sensors and wiring are correct and the error reappears after a reset, the board is the cause. Check PCB voltages and rule out wiring/display faults before reprogramming or replacing. |
| F64 | Fault in the main PCB / rapid fluctuation of the flow/return sensor | The PCB electronics interpret erratic readings from the NTC due to input/ADC failure; if the NTC and its wiring measure correctly, the cause is the PCB. Confirm with ohmic measurement of the NTC and continuity to the PCB. |
| F65 | Excessive temperature of the main PCB | The internal thermal sensor of the PCB detects overheating due to dissipation failure or the circuit itself; if there is no external overheating, the board is defective. Check ventilation/location and actual temperature; if the fault code appears when cold, replace the PCB. |
| F67 | Flame signal fault on the main PCB | The ionization circuit of the PCB is not correctly processing the flame current; if the electrode, ground, and cable are correct and the signal is stable, the fault is in the control board. Check ionization microamps and continuity to the PCB. |
| F70 | User interface incompatible with the main PCB / incorrect product code | After changing the control board or display, the DSN/coding does not match between the UI and PCB; the board needs parameterization or is of incorrect reference. Verify that the DSN on the display matches the data plate and reprogram according to the manual; if it does not accept, incorrect board. |
These symptoms can have more than one cause. If your boiler displays a fault code, send it to us via WhatsApp along with a photo of the labeling, and we'll tell you if this is the part.
Data sheet for the PCB Airsol 3001060232
- Catalogue reference
- 3001060232
- Brand
- Airsol
- Type of part
- PCBs (control boards)
- Units in stock
- 4 units
- Status
- Refurbished
- Warranty
- 1 year
- Shipping
- Delivery time shown at checkout
- Return
- 14 days
Data read on the part and in the manufacturer's documentation
What we have not been able to verify does not appear here.
- Display module
- Independent, connected to the PCB by flat cable.
Frequently asked questions about the PCB 3001060232
Does this Airsol PCB Ref. 3001060232 work for my Heatline Compact S24S?
Does the PCB for the Heatline Compact S30 include the control display?
What is the difference between the display module of this PCB and the PCB itself in the Heatline Compact S24?
Spare parts related to Airsol Heatline Compact (non-condensing / Airsol HK B124)
