Beretta Arte 24 C S I N PCB Ref. R10023537
Beretta Arte 24 C S I N PCB (control board) Ref. R10023537, responsible for controlling the ignition, burner modulation, pump, and safety features of the boiler. When it fails, the boiler does not start, locks out, or exhibits erratic operation, potentially displaying fault code 01: Lockout due to flame failure. It is compatible with boilers from the Beretta Ciao N and Arte N ranges, such as the Arte 24 CSI N model, among others. It should be replaced when these malfunction symptoms are detected.
VAT included
Consult via WhatsAppBeretta boilers compatible with reference R10023537
PCB with reference R10023537. Five confirmed compatibilities: Ciao 24 CAI N and Ciao 24 CSI N.
Proven compatibility
| Boiler model | Family | Verification |
|---|---|---|
| Beretta Ciao 24 CAI N | Beretta Ciao N | Contrasted |
| Beretta Ciao 24 CSI N | Beretta Ciao N | Contrasted |
| Beretta Ciao 28 CAI N | Beretta Ciao N | Contrasted |
| Beretta Ciao 28 CSI N | Beretta Ciao N | Contrasted |
| Beretta Arte 24 CSI N | Beretta Arte N | Contrasted |
Can't see your model or have questions? The printed reference takes precedence. How to check it · Send us a photo via WhatsApp.
How to check if ref. R10023537 is the part for your boiler
What determines it is not the boiler model, but the reference printed on the part you already have installed.
- Find the reference printed on the installed part and check whether it matches the catalogue reference R10023537. If it is not visible, do not identify the part from its shape alone.
- Check the full boiler model on its data plate and look for it in the model associations on this page.
- Compare the connections and physical body with the original part before installation.
- If anything is unclear, send us a photo of the marking via WhatsApp before placing your order.
Symptoms and faults that the PCB R10023537 resolves.
The PCB controls the ignition, modulation, and safety features of the boiler. These are the typical symptoms and what to do:
Common symptoms and faults
- 01
Different fault codes appear each time, with no clear relation to a specific fault.
Cause: The PCB misinterprets some signals and causes incorrect lockouts.
Reset the boiler and check if the fault code is always the same or changes each time.
- 02
The domestic hot water works but the heating doesn't heat, or only one of the two works.
Cause: The PCB controls each function separately and one can fail without affecting the other.
Check the domestic hot water and heating separately before assuming that the PCB is faulty.
- 03
The boiler is experiencing short and frequent start-ups and shutdowns, even though no one is requesting heat.
Cause: A relay on the PCB that switches incorrectly causes cycles that do not correspond to any real demand.
Check that there is no faulty room thermostat that is continuously calling for heat.
- 04
The boiler control does not respond or gets stuck.
Cause: The PCB processes the commands from the remote; if it fails, there is no response even if the remote is functioning properly.
Try another compatible remote control if you have one on hand, or check that the remote control connector to the PCB is properly connected.
Fault codes for Beretta that this part resolves.
| Code | Fault | Diagnosis and solution |
|---|---|---|
| 01 | Lockout due to absence of flame (indicated as solid red LED on Ciao N). | The CP08 control board may fail in managing/delivering ignition/ionization commands or in flame supervision, causing lockout 01; if, after checking electrodes, gas, and wiring, the issue persists, the manual itself indicates replacing the control board. To confirm, measure voltages on the board (e.g., 230 VAC at CN1.2–CN1.3 and ignition checks); if everything is correct and there is no ignition, replace the PCB. |
These symptoms can have more than one cause. If your boiler displays a fault code, send it to us via WhatsApp along with a photo of the labeling, and we'll tell you if this is the part.
Data sheet for the Beretta R10023537 PCB.
- Catalogue reference
- R10023537
- Brand
- Beretta
- Type of part
- PCBs (control boards)
- Units in stock
- 2 units
- Status
- Refurbished
- Warranty
- 1 year
- Shipping
- Delivery time shown at checkout
- Return
- 14 days
Data read on the part and in the manufacturer's documentation
What we have not been able to verify does not appear here.
- current
- 5 A
- This PCB shares a design with other units in the catalog, but it is a different physical piece; it is not claimed to be the same transformer reference.
Frequently asked questions about the PCB R10023537
Is this PCB suitable for the three Beretta boilers Arte 24 CSI/CAI, Ciao 24 CSI N, and Ciao 28 CAI/CSI?
Spare parts related to Beretta Ciao N
