Main Control PCB Vaillant VMW ES 24 282 3 5 Ref. 130859
The Main Control PCB for Vaillant VMW ES 24 282 3 5 Ref. 130859 is responsible for managing the ignition, burner modulation, pump, and safety features of the boiler. If it malfunctions, the boiler may fail to start, become locked, or behave erratically, displaying fault codes such as F.63, F.64, or F.67. This part is compatible with boilers from the Turbomax Plus range, including models VMW ES 24 282/3-5 and VMW 24/282/3-5, among others. It is recommended to replace it upon detecting these symptoms or if it fails to operate correctly.
VAT included
Consult via WhatsAppVaillant boilers compatible with reference 130859
PCB with reference 130859. Four confirmed compatibilities: VMW ES 24 282/3-5 and VMW ES 282/3-5.
Proven compatibility
| Boiler model | Family | Verification |
|---|---|---|
| Vaillant VMW ES 24 282/3-5 | Turbomax Plus | Contrasted |
| Vaillant VMW ES 282/3-5 | Turbomax Plus | Contrasted |
| Vaillant VMW 24/282/3-5 | Turbomax Plus | Contrasted |
| Vaillant VMW 282/3-5 | Turbomax Plus | Contrasted |
Can't see your model or have questions? The printed reference takes precedence. How to check it · Send us a photo via WhatsApp.
How to check if ref. 130859 is the part for your boiler
What determines it is not the boiler model, but the reference printed on the part you already have installed.
- Find the reference printed on the installed part and check whether it matches the catalogue reference 130859. If it is not visible, do not identify the part from its shape alone.
- Check the full boiler model on its data plate and look for it in the model associations on this page.
- Compare the connections and physical body with the original part before installation.
- If anything is unclear, send us a photo of the marking via WhatsApp before placing your order.
Symptoms and faults that the PCB 130859 resolves.
The PCB controls the ignition, modulation, and safety features of the boiler. These are the typical symptoms and what to do:
Common symptoms and faults
- 01
The boiler is completely dead, not a single light or the display turns on.
Cause: The PCB does not process or receive mains power, and cuts off all control.
With the boiler unplugged, check the internal fuse on the PCB before discarding it.
- 02
The display shows a fault code that didn't appear before.
Cause: Some component of the PCB that manages that specific function has failed.
Note the exact code and check the manual to see if it corresponds to an external sensor, such as the NTC sensor, before attributing it to the PCB.
- 03
The control panel does not respond to any button presses.
Cause: The PCB does not process the signals from the buttons or the internal communication bus fails.
Check that the connectors and the ribbon cable to the panel are properly seated and free of corrosion.
- 04
The boiler turns on by itself or cycles strangely without touching the thermostat.
Cause: The control electronics have lost stability and are giving erratic commands.
Check for any moisture or visible corrosion on the PCB before replacing it.
- 05
The configured parameters reset without apparent reason.
Cause: Memory fault in the PCB that stores those settings
Check if the problem coincides with a recent power outage, which can also reset parameters without the PCB being damaged.
Fault codes from Vaillant that this part resolves.
| Code | Fault | Diagnosis and solution |
|---|---|---|
| F.63 | Fault: EEPROM (electronics fault). | Corruption/invalid reading of the EEPROM memory on the PCB; check voltages and connectors on the board and, if it persists after reset, replace the PCB. |
| F.64 | Fault in the electronics / NTC (NTC short circuit or defective electronics). | NTC input or analogue stage of the PCB short-circuited/damaged; check NTC and wiring, and if the sensors are correct, diagnose/replace the PCB. |
| F.65 | Electronic system temperature too high. | Overtemperature detected on the PCB due to external influence or internal defect; check ventilation/location and, if it reappears when cold, replace the PCB. |
| F.67 | Electronic fault/flame: implausible flame signal (defective electronics). | The flame detection circuit on the PCB delivers an invalid signal; rule out electrode/ground and, if the ionisation is correct, the PCB is faulty. |
| F.70 | Invalid appliance code (DSN). | Display and/or PCB were replaced simultaneously without reprogramming the DSN/coding; verify and adjust DSN or coding resistor on the PCB. |
| F.97 | Main PCB self-test failed. | The PCB does not pass its internal self-test due to component/firmware default; repeat start-up and, if it persists, replace the control board. |
| with | No communication between the display and the PCB (communication fault). | The line and interface of the PCB do not communicate with the panel; check the bus/wiring and connectors, and if they are correct, the PCB (or the display) is faulty. |
| F.61 | Gas valve activation/operation error. | Fault in the valve driver/control on the PCB or PCB-valve communication; check the harness and valve coils, and if they are correct, the PCB is damaged. |
| F.62 | Gas valve switch-off delay. | The closing signal from the PCB arrives late/incorrectly or the board's driver fails; if the valve is sealed, the origin is the PCB (signal/power stage). |
| F.26 | Current of the stepper motor gas valve not plausible. | Reading/control stage fault in the PCB towards the stepper motor of the valve; if connections and valve are OK, the fault is in the PCB. |
These symptoms can have more than one cause. If your boiler displays a fault code, send it to us via WhatsApp along with a photo of the labeling, and we'll tell you if this is the part.
Data sheet for the Vaillant 130859 PCB.
- Catalogue reference
- 130859
- Brand
- Vaillant
- Type of part
- PCBs (control boards)
- Units in stock
- 2 units
- Status
- Refurbished
- Warranty
- 1 year
- Shipping
- Delivery time shown at checkout
- Return
- 14 days
Manuals and technical documentation
Official documentation of the boiler, useful for locating the part and cross-referencing the fault codes.
- Vaillant VMW ES 282/3-5 Manual (PDF)Document © Vaillant, provided as a technical reference.
Frequently asked questions about the PCB 130859
Is this PCB suitable for a VMW 282/3-5 boiler?
Is this PCB suitable for a VMWES28235?
Does the board have any readable component codes on the SMD chips?
Spare parts related to Vaillant Turbomax Plus
