Honeywell Smoke Pressure Switch Biasi GME24 C6065FH1227:2 Ref. BI1036102
Differential pressure switch for flue gases for Biasi GME24 boilers and related models. Manufactured by Honeywell (Yamatake-Honeywell), model C6065FH1227:2, set at 1.33 mbar with a maximum of 6 mbar. It checks the flue gas pressure before allowing the burner to ignite; if it detects a value out of range, it locks the boiler. It is replaced when the boiler does not ignite or stops due to a draft fault.
VAT included
Consult via WhatsAppBiasi boilers compatible with reference BI1036102
Pressure switch with reference BI1036102. A verified compatibility: Micon 24 E.
Proven compatibility
| Boiler model | Family | Verification |
|---|---|---|
| Biasi Micon 24 E | Micon | Contrasted |
Can't see your model or have questions? The printed reference takes precedence. How to check it · Send us a photo via WhatsApp.
How to check if ref. BI1036102 is the part for your boiler
What determines it is not the boiler model, but the reference printed on the part you already have installed.
- Find the reference printed on the installed part and check whether it matches the catalogue reference BI1036102. If it is not visible, do not identify the part from its shape alone.
- Check the full boiler model on its data plate and look for it in the model associations on this page.
- Compare the connections and physical body with the original part before installation.
- If anything is unclear, send us a photo of the marking via WhatsApp before placing your order.
Symptoms and faults that the pressure switch BI1036102 resolves.
The pressure switch controls the air or water pressure to authorize operation. These are the typical symptoms and what to do:
Common symptoms and faults
- 01
The boiler goes through the ignition cycle, the fan spins, but it stops and locks out before the flame ignites.
Cause: The flue pressure switch does not detect sufficient depression in the exhaust, and the control unit does not allow gas flow.
Check that the flue gas outlet duct is not obstructed, crushed, or has too much horizontal run before replacing the pressure switch.
- 02
The display shows a flue or exhaust fault code.
Cause: It is the reading given by the control unit when the pressure switch does not close the contact within the safety time.
Check the silicone tubes connecting the pressure switch to the duct: make sure they are not bent, punctured, or disconnected.
- 03
The boiler shuts off on its own while in operation, not just when turning on.
Cause: A pressure variation in the exhaust during combustion causes the pressure switch to open the contact and shut off the burner for safety.
Check that the flue outlet to the outside is not facing against the wind, has no bird nests, or is not obstructed.
- 04
The fan sounds and spins normally, but the boiler still locks out.
Cause: If the fan is working properly, the draft fault usually comes from the pressure switch or its pressure connections, not the motor.
With the boiler off, use a multimeter to check that the pressure switch closes the contact when gently blowing through the tube, before considering it faulty.
Fault codes for Biasi that this part resolves.
| Code | Fault | Diagnosis and solution |
|---|---|---|
| E05 | Flue pressure switch anomaly | A problem has been detected in the flue gas evacuation. This can be dangerous and requires immediate attention. If the boiler shows this code, it is possible that the flue pressure switch is faulty or there is a blockage in the evacuation system. |
These symptoms can have more than one cause. If your boiler displays a fault code, send it to us via WhatsApp along with a photo of the labeling, and we'll tell you if this is the part.
Datasheet for the Biasi BI1036102 pressure switch
- Catalogue reference
- BI1036102
- Brand
- Biasi
- Type of part
- Pressure switches
- Units in stock
- 5 units
- Status
- Refurbished
- Warranty
- 1 year
- Shipping
- 1-2 business days
- Return
- 14 days
Data read on the part and in the manufacturer's documentation
What we have not been able to verify does not appear here.
- Component code
- C6065FH1227:2
- Electrical marking (silkscreen)
- 1.5(0.5)μ 250V~
- Set pressure
- P= 1.33 mbar
- Maximum pressure
- 6 mbar
- CE marking
- CE-0063AP3085/1
- Batch code/date
- 0008D
- Contact settings
- NC — C — NO (microswitch)
- Manufacturer (embedded in casing)
- Yamatake-Honeywell — Made in Japan
- Additional marking on the rear label
- GME 24 ES N249150301
Frequently asked questions about the pressure switch BI1036102
Is this pressure switch suitable for the Biasi GME24?
Who manufactures the pressure switch for the Biasi GME24, Honeywell or Biasi?
What fault does this pressure switch resolve in the GME24?
What pressure is the pressure switch of the Biasi GME24 set to?
How can I identify if my boiler is compatible with the pressure switch PREMNGME24?
Spare parts related to Biasi Micon
