Junkers Euromaxx Air Pressure Switch ZWC24-1MFA23 - Huba Control 605.99549
RefurbishedJunkersPressure switchesHuba Control

Junkers Euromaxx Air Pressure Switch ZWC24-1MFA23 - Huba Control 605.99549

Stock · 1 unit

Air pressure switch manufactured by Huba Control (code 605.99549), installed in Junkers Euromaxx boilers ZWC24, ZWC24-1MF2A23, ZWC24-1MFA23, ZWC24-1MFA31, and ZWC28-1MFA. The reference printed on the label (8-716-771-175) matches the catalog reference 87167711750. It monitors the differential combustion air pressure (40/30 Pa) and interrupts ignition if the draft is not correct.

VAT included

Compatibility

Junkers boilers compatible with reference 87167711750

Pressure switch with reference 87167711750. Six confirmed compatibilities: ZWC24-1MFA 23 and ZWC24-1MFA 31.

Proven compatibility

Boiler modelFamilyVerification
Junkers ZWC24-1MFA 23Junkers Euromaxx ZWC24-1MFAContrasted
Junkers ZWC24-1MFA 31Junkers Euromaxx ZWC24-1MFAContrasted
Junkers ZWC24-1MF2A 23Junkers Euromaxx ZWC24-1MFAContrasted
Junkers ZWC24-1MF2A 31Junkers Euromaxx ZWC24-1MFAContrasted
Junkers ZC24-1MFA 23Junkers Euromaxx ZWC24-1MFAContrasted
Junkers ZC24-1MFA 31Junkers Euromaxx ZWC24-1MFAContrasted

Can't see your model or have questions? The printed reference takes precedence. How to check it ·

Guide

How to check if ref. 87167711750 is the part for your boiler

What determines it is not the boiler model, but the reference printed on the part you already have installed.

  1. Find the reference printed on the installed part and check whether it matches the catalogue reference 87167711750. If it is not visible, do not identify the part from its shape alone.
  2. Check the full boiler model on its data plate and look for it in the model associations on this page.
  3. Compare the connections and physical body with the original part before installation.
  4. If anything is unclear, send us a photo of the marking via WhatsApp before placing your order.
Diagnosis and fault codes

Symptoms and faults that the pressure switch 87167711750 resolves.

The pressure switch controls the air or water pressure to authorize operation. These are the typical symptoms and what to do:

Common symptoms and faults

  • 01

    The boiler tries to ignite, the fan starts but the burner does not light and it locks out.

    Cause: The pressure switch does not detect the necessary air pressure drop, and the control board does not allow the gas to flow.

    Make sure the fan is spinning freely and at a good speed before checking the pressure switch.

  • 02

    The boiler shuts down by itself a few seconds after starting, as if it loses draft.

    Cause: A partial obstruction in the flue duct causes the pressure switch to lose the pressure signal during the cycle.

    Check the flue pipe and the external terminal for any obstructions (nests, leaves, excessive wind).

  • 03

    The boiler needs to be reset several times in a row for it to start.

    Cause: The pressure switch oscillates between opening and closing the contact because the pressure signal reaches just at the set limit.

    Check that the silicone tubes going to the pressure switch are not bent, cracked, or have condensed water inside.

  • 04

    The fan can be heard running, but the boiler never goes into the ignition phase.

    Cause: Without the pressure switch contact closure, the control board does not authorize the opening of the gas valve for safety reasons.

    With the extractor running, use a multimeter to check if the pressure switch closes the contact; if it doesn't close even at the maximum extractor setting, the fault may be earlier, in the flue itself.

Fault codes from Junkers that this part resolves.

CodeFaultDiagnosis and solution
C1The pressure switch has activated during operation.The differential pressure switch opens during operation due to a fatigued diaphragm or intermittent microcontact, causing the signal to be lost to the Heatronic. Check the continuity of the pressure switch while the fan is running and measure the depression/differential with a manometer on the sampling tubes.
C4The pressure switch does not open in the rest position.The pressure switch remains stuck/closed at rest due to mechanical failure or residual pressure in the connections. With the fan stopped, verify that the contact is open and that there is no water column/obstructions in the tubes; check with a multimeter and manometer.
C6The pressure switch does not close.The pressure switch does not switch to closed when the fan starts due to internal misalignment or a damaged diaphragm, preventing combustion authorization. Verify that when the fan starts, the contact closes (continuity test) and that the achieved depression exceeds the pressure switch threshold (measurement at ports).

These symptoms can have more than one cause. If your boiler displays a fault code, send it to us via WhatsApp along with a photo of the labeling, and we'll tell you if this is the part.

Technical data

Datasheet for Junkers pressure switch 87167711750

Catalogue reference
87167711750
Brand
Junkers
Type of part
Pressure switches
Units in stock
1 unit
Status
Refurbished
Warranty
1 year
Shipping
1-2 business days
Return
14 days

Data read on the part and in the manufacturer's documentation

What we have not been able to verify does not appear here.

part code (Huba Control)
605.99549
differential pressure
40/30 Pa
current/voltage
1(0.5) A / 250 V~
batch
AVXCFD
printed reference
8-716-771-175
Documentation

Manuals and technical documentation

Official documentation of the boiler, useful for locating the part and cross-referencing the fault codes.

Frequently Asked Questions

Frequently asked questions about the pressure switch 87167711750

Does this air pressure switch work for a Junkers Euromaxx ZWC24-1MFA31?
Yes, that boiler is on the list of compatible models, along with ZWC24-1MFA23, ZWC24-1MF2A23, and others.
Who manufactures this pressure switch for the Euromaxx ZWC24-1MFA23?
Huba Control, according to the code 605.99549 engraved on the body of the part.
Does the reference printed on the label match the 87167711750 from the store?
Yes, the label prints 8-716-771-175, which is the same catalog number without separators.
What air differential pressure does this pressure switch control?
40/30 Pa; it cuts off the ignition if the combustion draft does not reach that value.
What fault causes a failure in this air pressure switch?
It prevents the burner from igniting because the boiler detects that the differential air pressure does not reach the cut-off value, even though the draft is correct.
What is the reference for this air pressure switch?
The reference is PJE-1MFA 23.

Spare parts related to Junkers Junkers Euromaxx ZWC24-1MFA

Delivery 1–2 daysworking days, mainland Spain
1-year warrantyreviewed and tested
14-day returnuninstalled parts
Technical supportwe verify your model
Junkers Euromaxx Air Pressure Switch ZWC24-1MFA23 - Huba Control 605.99549