Domestic Hot Water Flow Switch Beretta Mynute Green 28 CSI Ref. R10022348
The Mynute Green boilers, such as the 28 CSI model, use the Beretta ACS flow switch, reference R10022348. This component detects the flow of water when a tap is opened and activates the ignition for the production of domestic hot water. If it fails, you will notice that no hot water comes out even when the tap is open. This flow switch is compatible with the Mynute Green range. You should replace it when you experience issues with hot water production.
VAT included
Consult via WhatsAppBeretta boilers compatible with reference R10022348
Flow meter with reference R10022348. A proven compatibility: Mynute Green 28 CSI.
Proven compatibility
| Boiler model | Family | Verification |
|---|---|---|
| Beretta Mynute Green 28 CSI | Mynute Green | Contrasted |
Can't see your model or have questions? The printed reference takes precedence. How to check it · Send us a photo via WhatsApp.
How to check if the part R10022348 is the one for your boiler
What determines it is not the boiler model, but the reference printed on the part you already have installed.
- Find the reference printed on the installed part and check whether it matches the catalogue reference R10022348. If it is not visible, do not identify the part from its shape alone.
- Check the full boiler model on its data plate and look for it in the model associations on this page.
- Compare the connections and physical body with the original part before installation.
- If anything is unclear, send us a photo of the marking via WhatsApp before placing your order.
Symptoms and faults that the flow meter R10022348 resolves.
The flow meter detects the passage of water to activate the domestic hot water. These are the typical symptoms and what to do:
Common symptoms and faults
- 01
The boiler does not start when the hot water tap is opened, but the heating works correctly.
Cause: The flow detector informs the control board that hot water is needed; if it does not detect the flow of water, the burner does not activate.
Open the tap to the maximum: if it doesn't ignite with low pressure but does at full, check the network pressure or a dirty filter.
- 02
The hot water comes out intermittently, it stops and then comes out again without touching the faucet.
Cause: A turbine or blade of the detector that is dirty or rubbing sends intermittent signals to the control board.
Check that the cold water inlet filter, just before the sensor, is free of scale or debris that could interrupt the flow.
- 03
An error code related to the flow sensor appears on the display.
Cause: The control unit indicates that the signal from the detector is not arriving or is arriving incorrectly.
Check that the 4-way electrical connector is properly connected and dry before considering the part faulty.
- 04
Water leak in the area where the sensor is mounted, near the brass fitting.
Cause: The brass fitting and the gasket of the sensor may lose tightness over time.
Gently tighten the fitting without forcing it, and check the visible gasket before deciding to replace the entire part.
These symptoms can have more than one cause. If your boiler displays a fault code, send it to us via WhatsApp along with a photo of the labeling, and we'll tell you if this is the part.
Flow meter sheet Beretta R10022348
- Catalogue reference
- R10022348
- Brand
- Beretta
- Type of part
- Flow detectors
- Units in stock
- 1 unit
- Status
- Refurbished
- Warranty
- 1 year
- Shipping
- 1-2 business days
- Return
- 14 days
Data read on the part and in the manufacturer's documentation
What we have not been able to verify does not appear here.
- Connection fitting
- Brass
- Electrical connector
- 4-way
- Compatibility confirmed only with Beretta Mynute Green 28 CSI.
Manuals and technical documentation
Official documentation of the boiler, useful for locating the part and cross-referencing the fault codes.
- Beretta Mynute Green 28 CSI Manual (PDF)Document © Beretta, provided as a technical reference.
Frequently asked questions about the flow meter R10022348
Is this flow detector suitable for a Beretta Mynute Green 28 CSI?
When should this flow detector be replaced in the Mynute Green 28 CSI?
What type of connections does the flow detector of the Beretta Mynute Green 28 CSI have?
Spare parts related to Beretta Mynute Green
