Vaillant Boiler PCB VCM 182/1 E and Compatible Models
The PCB for the Vaillant VCM 182/1 E boiler and compatible models, reference 130438, is the brain of the boiler that controls ignition, burner modulation, the pump, and safety features. When it malfunctions, the boiler may fail to start, become locked, or exhibit erratic operation. Users may observe fault codes such as F.61, F.62, F.63, F.64, or F.65. This PCB is compatible with models such as the VCM 182/1 E, VCM 242/1 E, VCM 282/1 E, among others. It is recommended to replace the PCB when the mentioned symptoms are detected or in case of any operational faults.
VAT included
Consult via WhatsAppVaillant boilers compatible with reference 130438
PCB with reference 130438. Eight confirmed compatibilities: VCM 182/1 E and VCM 242/1 E.
Proven compatibility
| Boiler model | Family | Verification |
|---|---|---|
| Vaillant VCM 182/1 E | Turboblock VCM (series /1 E) | Contrasted |
| Vaillant VCM 242/1 E | Turboblock VCM (series /1 E) | Contrasted |
| Vaillant VCM 282/1 E | Turboblock VCM (series /1 E) | Contrasted |
| Vaillant VCM 240/1 | Turboblock VCM (series /1 E) | Contrasted |
| Vaillant VCM 260/1 | Turboblock VCM (series /1 E) | Contrasted |
| Vaillant VCM 180/1 | Turboblock VCM (series /1 E) | Contrasted |
| Vaillant VC 240/1 | VC (series /1 E) | Contrasted |
| Vaillant VC 242/1 E | VC (series /1 E) | Contrasted |
Can't see your model or have questions? The printed reference takes precedence. How to check it · Send us a photo via WhatsApp.
How to check if ref. 130438 is the part for your boiler
What determines it is not the boiler model, but the reference printed on the part you already have installed.
- Find the reference printed on the installed part and check whether it matches the catalogue reference 130438. If it is not visible, do not identify the part from its shape alone.
- Check the full boiler model on its data plate and look for it in the model associations on this page.
- Compare the connections and physical body with the original part before installation.
- If anything is unclear, send us a photo of the marking via WhatsApp before placing your order.
Symptoms and faults that the PCB 130438 resolves.
The PCB controls the ignition, modulation, and safety features of the boiler. These are the typical symptoms and what to do:
Common symptoms and faults
- 01
The boiler does not ignite and there are no lights or signals on the panel.
Cause: The PCB does not distribute power to the components; if it fails, the boiler does not receive energy.
Check the fuse on the PCB and verify that there is power at the input connector before replacing it.
- 02
An error code appears that does not match any damaged component.
Cause: The control board incorrectly interprets the signals from the sensors and locks the boiler without a real reason.
Check the code in the manual and review the indicated component before assuming that the PCB is faulty.
- 03
The burner turns on and off repeatedly, without stabilizing.
Cause: A fault in the PCB causes erratic ignitions, as if it loses and regains the ignition signal.
Check that the flue and the temperature sensor are in good condition before concluding that it is the PCB.
- 04
The fuse on the PCB burns out quickly after replacing it, every time you try to turn on the boiler.
Cause: A damaged internal component causes a short circuit that overloads the fuse.
If the fuse blows several times in a row when you replace it, do not continue trying to turn on the boiler: it is a sign of an internal fault.
Fault codes from Vaillant that this part resolves.
| Code | Fault | Diagnosis and solution |
|---|---|---|
| F.61 | Gas valve activation error. | The relay/output stage of the PCB (auxiliary/main) does not correctly switch the gas valve. Check the power supply to the valve at the terminals, continuity of the harness, and if everything is correct, replace the PCB to confirm. |
| F.62 | Delay in gas valve disconnection. | The PCB keeps the gas valve energized longer than it should (control/relay fault). Check that the valve closes properly and that the wiring is correct; if the issue persists, measure the control voltage and confirm by replacing the PCB. |
| F.63 | Fault: EEPROM (electronics). | Corruption/defect of the EEPROM memory on the PCB. Check resets and parameters; the standard check is to replace the board with a new or programmed one to rule out the fault. |
| F.64 | Fault in the electronics/NTC. | Fault in the measurement/ADC stage or sensor power supply on the PCB. Check NTC and wiring; if the sensors measure correctly but the fault code persists, the cause is the PCB. |
| F.65 | Fault: electronics temperature too high. | The thermal sensor on the PCB detects overheating or the PCB itself is damaged. Check ventilation/location and temperatures; if they are normal and the error repeats, replace the PCB. |
| F.67 | Fault: electronics/flame (flame signal not plausible). | The detection/ionization stage on the PCB delivers an incoherent signal. Check the electrode, cable, and polarity; if everything is correct, the fault is in the PCB. |
These symptoms can have more than one cause. If your boiler displays a fault code, send it to us via WhatsApp along with a photo of the labeling, and we'll tell you if this is the part.
Data sheet for the Vaillant 130438 PCB.
- Catalogue reference
- 130438
- Brand
- Vaillant
- Type of part
- PCBs (control boards)
- Units in stock
- 5 units
- Status
- Refurbished
- Warranty
- 1 year
- Shipping
- 1-2 business days
- Return
- 14 days
Manuals and technical documentation
Official documentation of the boiler, useful for locating the part and cross-referencing the fault codes.
- Vaillant VCM 182/1 E Manual (PDF)Document © Vaillant, provided as a technical reference.
Frequently asked questions about the PCB 130438
Is this PCB compatible with the boiler VCM 182/1 E?
How many models are compatible with this PCB?
What fault codes are compatible with this PCB?
Can I use this PCB in a VCM 240/1 boiler?
Is the PCB suitable for the VC 242/1 E range?
Spare parts related to Vaillant Turboblock VCM (series /1 E)
